C7 - problem with ZEN25

[dadarkgtprince]

@k5map

Where can I find this info?

Select the parent device from your Devices menu. Scroll to the bottom. Under Device Details, there is one row labeled Data. You'll find the firmwareVersion in there

[k5map]

I did as you stated but do not see the firmware version (pic attached)

[dadarkgtprince]

Weird, it shows it on my C-5

C-5:

I'll need to take the device closer to my C-7 to pair it since I haven't built that network up yet. I'll try it this weekend and post an update

[neonturbo]

I think you can also get this with the Basic Zwave tool. It will report in the logs. Change to that tool as the driver, get a Version Report, and swap back to the correct driver.

Super basic Z-Wave parameter tool

I just published a very basic Z-Wave tool for setting device parameters for all the tweakers out there...

[Rxich]

Mine shows right under capabilities in device page. Although I'm using a non HE native driver ( ahem- not really 3rd party, but a developer that the manufacturers rely on for drivers)
Try the driver by krlaframboise

I used an aeon zstick 5 to upgrade

[danabw]

@Rxich

krlaframboise

krlaframboise himself has said in his Zooz double plug driver thread that there was no reason to use his after the built-in driver was added to Hubitat.

@krlaframboise

Hubitat ended up adding support for the USB reporting to their built-in handler and I think it also supports all the settings in the latest firmware so you're correct, there's no reason to use this handler. (I forgot I wrote a custom Hubitat handler and responded from my phone thinking this was the ST forum)

I used both his and the Hubitat driver and neither resolved my problems w/the plug, unfortunately. Mine had FW 2.0 and I had nothing but problems w/the plug, so having 2.0 is not a panacea...but you'd think should help.

[k5map]

I'm not seeing the firmware version in my device details... also, my HE does not show the 2 child devices to control each plug individually. Might have to give the other driver a trail run.

[krlaframboise]

@danabw

I used both his and the Hubitat driver and neither resolved my problems w/the plug

I'm not sure if the code changes required for S2 have been made public so I haven't added them to any of my custom handlers yet.

This device has tons of settings and Hubitat can rarely handle them all in a single attempt so you often have to click the configure button about a minute after joining the device and then refresh the page in order to see the children and everything that should be in the data section.

[k5map]

I just clicked the Configure and then Refresh buttons and did not see any change in my Device page but did see something interesting in the log. But still do not see the 2 child devices to control each outlet individually.

Summary

dev:462020-08-15 12:19:26.165 pm debugRight Outlet Auto Turn-On After(#15) = 60

dev:462020-08-15 12:19:25.957 pm debugRight Outlet Auto Turn-On Timer Enabled(#14) = 0

dev:462020-08-15 12:19:25.656 pm debugLeft Outlet Auto Turn-On After(#11) = 60

dev:462020-08-15 12:19:25.431 pm debugLeft Outlet Auto Turn-On Timer Enabled(#10) = 0

dev:462020-08-15 12:19:25.170 pm debugRight Outlet Auto Turn-Off After(#13) = 60

dev:462020-08-15 12:19:24.922 pm debugRight Outlet Auto Turn-Off Timer Enabled(#12) = 0

dev:462020-08-15 12:19:24.654 pm debugLeft Outlet Auto Turn-Off After(#9) = 60

dev:462020-08-15 12:19:24.407 pm debugLeft Outlet Auto Turn-Off Timer Enabled(#8) = 0

dev:462020-08-15 12:19:24.140 pm debugElectrical Current Reporting Frequency(#6) = 300

dev:462020-08-15 12:19:23.898 pm debugVoltage Reporting Frequency(#5) = 300

dev:462020-08-15 12:19:23.636 pm debugEnergy Reporting Frequency(#4) = 300

dev:462020-08-15 12:19:23.362 pm debugPower Reporting Frequency(#3) = 30

dev:462020-08-15 12:19:23.119 pm debugPower Reporting Threshold(#2) = 5

dev:462020-08-15 12:19:22.835 pm debugLED Indicator Mode(#17) = 1

dev:462020-08-15 12:19:22.606 pm debugManual Control(#16) = 1

dev:462020-08-15 12:19:22.340 pm debugOverload Protection(#7) = 10

dev:462020-08-15 12:19:22.112 pm debugOn/Off Status Recovery After Power Failure(#1) = 0

dev:462020-08-15 12:19:21.518 pm debugFirmware: 2.0

[krlaframboise]

@k5map

I just clicked the Configure and then Refresh buttons and did not see any change in my Device page but did see something interesting in the log.

I meant refresh the web page after clicking configure...

[k5map]

Well after waiting alot longer than I expected, the info now shows the firmware version but still do not have the 2 child outlet control

[mike.maxwell]

Details on S2 security updates are in the 2.2.3 release notes.

[k5map]

For those who have this device setup and working correctly, I'm curious as to the security option chosen when pairing this device,.. S2 C0, S2, C1 or S2 C2

[Rxich]

Mine is NOT joined securely on my C4

[k5map]

When I joined mine and checked S0, S2 C0 and S2 C1... my C7 now adds it as a Power Strip. Geez this is getting a bit frustrating.

[danabw]

Cut your losses...grab the plug and walk outside, throw it as far as you can down the street. Then run back in and shut your door and lock it.

[dadarkgtprince]

This is on my C-7

It did pull it in as a power strip though, and not the double plug

[dadarkgtprince]

https://products.z-wavealliance.org/products/3192

When you join it, you should do S2 Unauthenticated as that's what it supports

This was after a few disconnects and reconnects. It does show the S2 security and the firmware.

One thing to note though, it still hasn't produced the child devices to control each plug individually

[danabw]

did you make sure I got the correct device driver? Several of my attempts to include it it would come in as a plane quote "Device" and I had to select the driver manually.

[dadarkgtprince]

I had it show up as Zooz Power Strip or Device, it never pulled it in as Zooz Double Plug. I had to manually change it each time