Zigbee with gen4 Shelly work?

[kkossev]

Probably Shelly does not like the old ZCL version (non-ZIgbee 3.0) reported from C-7 ?

Knockturn Alley

================================================================================================
Node Descriptor

▸ Logical Type = Zigbee Router
▸ Complex Descriptor Available = No
▸ User Descriptor Available = No
▸ Fragmentation Supported (R23) = No
▸ Frequency Band = Reserved
▸ Alternate PAN Coordinator = No
▸ Device Type = Full Function Device (FFD)
▸ Mains Power Source = Yes
▸ Receiver On When Idle = Yes (always on)
▸ Security Capability = No
▸ Allocate Address = Yes
▸ Manufacturer Code = 0x1490
▸ Maximum Buffer Size = 108 bytes
▸ Maximum Incoming Transfer Size = 1613 bytes
▸ Primary Trust Center = No
▸ Backup Trust Center = No
▸ Primary Binding Table Cache = Yes
▸ Backup Binding Table Cache = No
▸ Primary Discovery Cache = Yes
▸ Backup Discovery Cache = Yes
▸ Network Manager = Yes
▸ Maximum Outgoing Transfer Size = 1613 bytes
▸ Extended Active Endpoint List Available = No
▸ Extended Simple Descriptor List Available = No

Power Descriptor

▸ Current Power Mode = Same as "Receiver On When Idle" from "Node Descriptor" section above
▸ Available Power Sources =
▸ Current Power Sources =
▸ Current Power Source Level = Critical

Endpoint 0x01

In Cluster: 0x0000 (Basic Cluster)

▸ 0x0000 | ZCL Version | req | r-- | uint8 | 08 = 8 | --
▸ 0x0004 | Manufacturer Name | opt | r-- | string | Shelly | --
▸ 0x0005 | Model Identifier | opt | r-- | string | 1PM | --
▸ 0x0007 | Power Source | opt | r-- | enum8 | 00 = Unknown | --

▸ 0x00 | Reset to Factory Defaults | opt

In Cluster: 0x0003 (Identify Cluster)

▸ 0x0000 | Identify Time | req | rw- | uint16 | 0000 = 0 seconds | --

▸ 0x00 | Identify | req
▸ 0x01 | Identify Query | req
▸ 0x40 | Trigger Effect | opt

In Cluster: 0x0004 (Groups Cluster)

▸ 0x0000 | Name Support | req | r-- | map8 | 00 = 00000000 | --

▸ 0x00 | Add Group | req
▸ 0x01 | View Group | req
▸ 0x02 | Get Group Membership | req
▸ 0x03 | Remove Group | req
▸ 0x04 | Remove All Groups | req
▸ 0x05 | Add Group If Identifying | req

In Cluster: 0x0005 (Scenes Cluster)

▸ 0x0000 | Scene Count | req | r-- | uint8 | 00 = 0 | --
▸ 0x0001 | Current Scene | req | r-- | uint8 | 00 = 0 | --
▸ 0x0002 | Current Group | req | r-- | uint16 | 0000 = 0 | --
▸ 0x0003 | Scene Valid | req | r-- | bool | 00 = False | --
▸ 0x0004 | Name Support | req | r-- | map8 | 00 = 00000000 | --

▸ 0x00 | Add Scene | req
▸ 0x01 | View Scene | req
▸ 0x02 | Remove Scene | req
▸ 0x03 | Remove All Scenes | req
▸ 0x04 | Store Scene | req
▸ 0x05 | Recall Scene | req
▸ 0x06 | Get Scene Membership | req

In Cluster: 0x0006 (On/Off Cluster)

▸ 0x0000 | On Off | req | r-p | bool | 00 = Off | 5..0

▸ 0x00 | Off | req
▸ 0x01 | On | req
▸ 0x02 | Toggle | req
▸ 0x40 | Off With Effect | opt
▸ 0x41 | On With Recall Global Scene | opt
▸ 0x42 | On With Timed Off | opt

In Cluster: 0x0702 (Metering (Smart Energy) Cluster)

▸ 0x0000 | Current Summation Delivered | req | r-- | uint48 | 000000000FA0 = 4000 | --
▸ 0x0001 | Current Summation Received | opt | r-- | uint48 | 000000000000 = 0 | --
▸ 0x0200 | -- | -- | r-- | map8 | 00 = 00000000 | --
▸ 0x0300 | Unit of Measure | req | r-- | enum8 | 00 = kWh & kW | --
▸ 0x0301 | Multiplier | opt | r-- | uint48 | 000000000001 = 1 | --
▸ 0x0302 | Divisor | opt | r-- | uint48 | 0000000F4240 = 1000000 | --
▸ 0x0303 | Summation Formatting | req | r-- | map8 | 1B = 00011011 | --
▸ 0x0306 | Metering Device Type | req | r-- | map8 | 00 = Electric Metering | --

▸ 0x00 | Zone Enroll Response | req
▸ 0x03 | -- | --
▸ 0x06 | -- | --
▸ 0x08 | -- | --

In Cluster: 0x0B04 (Electrical Measurement Cluster)

▸ 0x0000 | Measurement Type | req | r-- | map32 | 00000001 = 00000000000000000000000000000001 | --
▸ 0x0300 | ACFrequency | opt | r-- | uint16 | 1382 = 4994 | --
▸ 0x0400 | AC Frequency Multiplier | opt | r-- | uint16 | 0001 = 1 | --
▸ 0x0401 | AC Frequency Divisor | opt | r-- | uint16 | 0064 = 100 | --
▸ 0x0505 | RMS Voltage | opt | r-- | uint16 | 5516 = 21782 | --
▸ 0x0508 | RMS Current | opt | r-- | uint16 | 0000 = 0 | --
▸ 0x050B | Active Power | opt | r-- | int16 | 0000 = Infinity | --
▸ 0x0600 | AC Voltage Multiplier | opt | r-- | uint16 | 0001 = 1 | --
▸ 0x0601 | AC Voltage Divisor | opt | r-- | uint16 | 0064 = 100 | --
▸ 0x0602 | AC Current Multiplier | opt | r-- | uint16 | 0001 = 1 | --
▸ 0x0603 | AC Current Divisor | opt | r-- | uint16 | 0064 = 100 | --
▸ 0x0604 | AC Power Multiplier | opt | r-- | uint16 | 0001 = 1 | --
▸ 0x0605 | AC Power Divisor | opt | r-- | uint16 | 0064 = 100 | --

▸ No received commands

Endpoint 0xEF

In Cluster: 0xFC01 (Unknown Cluster)

▸ No attributes

▸ No received commands

In Cluster: 0xFC02 (Unknown Cluster)

▸ No attributes

▸ No received commands

Endpoint 0xF2

Out Cluster: 0x0021 (Green Power Cluster)

▸ No generated commands

Bindings Table

▸ Could not retrieve data

Neighbors Table

▸ Addr:4661 | Type:Zigbee Router | RxOnWhenIdle:Yes | Rel:Sibling | Permit Joining:No | Depth:1
▸ Addr:E03B | Type:Zigbee Router | RxOnWhenIdle:Yes | Rel:Sibling | Permit Joining:No | Depth:1
▸ Addr:2BD1 | Type:Zigbee Router | RxOnWhenIdle:Yes | Rel:Sibling | Permit Joining:No | Depth:3
▸ Addr:9CDF | Type:Zigbee Router | RxOnWhenIdle:Yes | Rel:Sibling | Permit Joining:No | Depth:1
▸ Addr:B450 | Type:Zigbee Router | RxOnWhenIdle:Yes | Rel:Sibling | Permit Joining:No | Depth:1
▸ Addr:2763 | Type:Zigbee Router | RxOnWhenIdle:Yes | Rel:Sibling | Permit Joining:No | Depth:1
▸ Addr:0000 | Type:Zigbee Coordinator | RxOnWhenIdle:Yes | Rel:Sibling | Permit Joining:No | Depth:0
▸ Addr:AE74 | Type:Unknown | RxOnWhenIdle:Yes | Rel:Unknown | Permit Joining:No | Depth:0

Routing Table

▸ Destination:0000 | Next Hop:2BD1 | Route Status:Active
▸ Destination:0000 | Next Hop:0000 | Route Status:Acti

Pairing to C-8 via Zigbee 3.0 repeaters was also not possible. I had to use the Double Luck Voodoo to clean up the C-8 Zigbee routing table, and only then it will pair directly to the hub.