I can try with mine, its one phase supply.
Hmmm, why did they label it UK version if it's not compatible with UK households? Strange.
Some industrial units have more than one phase
Most factories use 3
Andy
Oh, I see. This was an industrial unit? 3 Phase makes sense for industrial, 2 does not. Turn of the century power. The original generators installed at Niagara Falls in 1895 were 2 phase!
1 Like
Ah, Andy was shipped the Upper Kentucky version instead of the United Kingdom one. 
1 Like
Guys
I'm really sorry but I'm going to withdraw this driver.
The actual piece of kit that I have is a DSB28-ZWEU .
The original driver I released I managed to get working on this hardware.
I have since received a ZW095-C which does NOT work correctly with this driver.
I don't want to disappoint but until I can get this sorted I'll remove the driver from GitHub.
It may take a while!
Andy
Did you ever get the ZW095-C to work ??
you can try my driver: Hubitat/Drivers/aeotec-home-energy-meter-gen5.src at master · ClassicGOD/Hubitat · GitHub
I own ZW095-C 868.42MHz (EU) 3 Clamps 4 Phases 60A but the driver should work with any clamp configuration since it just asks the meter how many endpoints it has and creates appropriate number of child devices.
Keep in mind:
- While I don't take feature requests right now (I got the driver where I want it and moved on) it would be nice to have it tested by someone else.
- You have to Save Preferences at least once for it to start working
- There is no hand holding - need to know value to set for a parameter - refer to Aeotec documentation
3 Likes
I'll try that - thank you.
So far so good.
It's reporting back nicely - ZW095-C 868.42MHz (EU) 1 Clamp 1 Phase 60A
Many thanks, Simon
1 Like
Glad to hear that 
Thank you for testing.
Just moved my HEM V2 off of ST, finally. I dreaded it as I have quite a few rules setup. It was my last holdout, I will have to keep the ST hub running for my Arlo camera and Leviosa shades integration but all Z-wave and ZIgbee devices are now removed.
I am using your driver for the HEM and it seems to be working well. Thank you.
Evening, I've just bought a zw095-c (3 phase unit) on ebay.... I only needed a single phase one but I didn't read the advert correctly 
I was wondering if I could just wire all the phases together (current clamp and voltage wires) and report all three phases the same? It's spec says it's 240v 50hz which is OK for here in the UK.
Provided it shows voltage and current OK Id be happy; I could work out power myself.
Anybody any experience / thoughts on this before I start?
Hi,
I tried this one today and after installed both drivers and Save preference, I only got this to states:
- syncStatus : in progress (parameter: 3)
What FW version are you running? Is your meter included in secure mode? (if I remember correctly there were issues with setting the parameters if it was not included in secure mode)
I found the reason. It was because my main electric box is metal and when I closed the door, it actually loses z-wave. Now I moved energy meter outside of box, it seems to be working.
@classicgod But I have one more question, how those clamp readings are updated? As now it looks like those values are not updated until I press "refresh" on the child clamp device? Main device power readings are updated on the fly.
You need to configure groups correctly. You can read the documentation provided by Aeotec to find out what values you need. This is how I configured mine:
Ok, thanks. I will try your configuration now. But I need to check Aeotec config instructions. Thanks for the help!
I am having exactly the same issue.
When I save the preferences it always stops at " in progress (parameter: 7)"
The HEM joins "unsecured" and it won't give me any security options.
I want to try joining it securely to see if this helps with the parameter setting. I understand the HEM supports S2 security
So my question is:
How do I get my Hubitat C7 to offers me the Z Wave security options when joining this device!.
Reading various threads it appears there used to be an option in the Z Wave set up to force the security box option, but it seems to have disappeared (C7 with latest firmware) or am I missing something!
