I will think about straightening the criteria for showing the healthStatus as ‘online’. For these sensors which use the IAS (Intruder Alarm System) messaging, better criteria could be the reception of the IAS zone status report from the device. For the Tuya-specific messages (like this device) it should be something else, however.
Yes, I will gladly accept Pull Requests in GitHub... or you can just send me the changed/added code lines.
Update for the TS0202, it does not report Illuminance like many others in the list.
Might be worthwile adding this to the initial post in this thread.
Only motion and battery are reported
Contrary to the model: TS0601 Manufactuer / TZE200_3towulqd,
which is very similar in form factor. So take care which one you pick on Ali store
1 Like
Good point - updated!
1 Like
Any recommendations for a wall mounted mmWave sensor, I have a small cottage where it's impossible to place ceiling mounted sensors because of the way the ceiling is built (wood plank cathedral ceiling with foam insulation throughout, so no cavity at all).
[RELEASE] Aqara FP1 Human Presence Sensor (RTCZCGQ11LM)
I have several. Very reliable. Can be difficult to pair but once done no problems.
I have heard good things, never saw one in person but looking at pictures, they are ugly as heck! Would much rather have a square box than that bulgy thing that looks like a wart 
Saw a couple on AliExpress, might just buy one and hope for the best.
I have 2. Both failed. I've heard reports of others that have units that failed. You get no support if they do.
Sorry to hear that. Hope mine continue to work 
. How long did they work for?
Advanced options are not available for some products of the Tuya presence sensor after a driver update.
The data section does not appear to be imported properly.
Current States
- battery : 5
- healthStatus : online
- illuminance : 2
- motion : active
- powerSource : battery
- tamper : detected
- temperature : 7.3
The reason is that the Data section of the device is wiped out ! 
Just checked the driver code, there are no device.updateDataValue() or device.removeDataValue() calls..
This is the second time when mysterious deletion of device Data properties is reported...
Do you remember when this problem happened? Immediately after the driver was updated, or probably after a hub reboot?
You can restore the missing Data section values by switching manually to HE inbuilt driver 'Device', clicking on 'GetInfo' button while waking up the sensor at the same time, then pressing F5 to refresh the web page and verify that the Data section model and manufacturer are there.
1 Like
It worked normally after today's update.
This is a sensor used in the bathroom, and suddenly the toilet switch repeatedly turned on/off.
I checked the driver and confirmed that the advanced option did not work.
I pair again several times, but the result was the same.
So as a last resort, I deleted it and connected it again, and now it works fine.
The two sensors in question are those that were exchanged using the 'Swap Apps Device' last week. Only these two sensors had problems at the same time.
Device pairing info
Manufacturer: _TZE200_ikvncluo
Endpoint 01 application: 44
Endpoint 01 endpointId: 01
Endpoint 01 idAsInt: 1
Endpoint 01 inClusters: 0000,0004,0005,EF00
Endpoint 01 initialized: true
Endpoint 01 manufacturer: _TZE200_ikvncluo
Endpoint 01 model: TS0601
Endpoint 01 outClusters: 0019,000A
Endpoint 01 profileId: 0104
Endpoint 01 stage: 4
Device pairing info
Manufacturer: _TZE200_jva8ink8
Endpoint 01 application: 44
Endpoint 01 endpointId: 01
Endpoint 01 idAsInt: 1
Endpoint 01 inClusters: 0000,0004,0005,EF00
Endpoint 01 initialized: true
Endpoint 01 manufacturer: _TZE200_jva8ink8
Endpoint 01 model: TS0601
Endpoint 01 outClusters: 0019,000A
Endpoint 01 profileId: 0104
Endpoint 01 stage: 4
The problem appears to occur when using 'Swap Apps Device'.
Before that, it worked fine, but I don't know why it suddenly became a problem.
Current States
- battery : 100
- healthStatus : online
- illuminance : 2
- motion : inactive
- powerSource : dc
- tamper : detected
- temperature : 0.3
I used 'Device', but the result didn't change, and I solved the problem by pairing again only after deleting it.
Will the same problem (Data section deletion) happen if you swap devices that are not Tuya and you are using HE inbuilt drivers?
If yes, then it may be a good idea to create a new post so that Hubitat staff helps with a fix.
2 Likes
Maybe it's a Tuya sensor and a switch that I've used.
The switch is unlikely to have a significant impact on the data section.
Next time I'll take a close look.
1 Like
Does this only report illuminance when motion is triggered, or does it also periodically report the lux value?
Hi @Kaitlyn ,
I don't own this sensor, so I can't say for sure. Typically, these motion sensors report the illuminance only a few hundred milliseconds before the 'motion active' event, as the purpose is the automation rules to decide whether to turn the lights on based on the illuminance value ... This is not a dedicated lux sensor.
But you see that @user3874 in the other thread says that this device reports periodically the illuminance... With Tuya devices everything is possible! : )
The same problem occurred for others.
After simply updating through HPM updates, some devices may not be able to use the Advanced option.
Can you check if it is the same case - manufacturer or model missing from the device web page Data section?
1 Like
He's not at home right now, and it happened on a device at home.
Only some of the devices occurred, and unlike yesterday's me, it only occurred in wall-type products, not ceiling-type products.
What I have in common with my case yesterday is that it only occurred on some devices after the HPM update.
I talked to him.
If possible, please let the developer know the details of the problem.
