[Release] Generic Zigbee Drivers with Presence and Recovery

[markus]

@AnubizDK

Do you have to do anything after you update the driver..?

Unless it's a wall switch device no need to do anything, but good you mentioned it. For wall switch devices I'd recommend Initialize. Just sit back and enjoy the new drivers

[AnubizDK]

Thanks.. Enjoying your new drivers already..

BTW - i found a "PLEASE REPORT TO DEV" line in the log for a LLKZMK11LM dual relay using your "Zigbee - Generic Switch (with Presence)" driver ver. 1.0.0.1025:

dev:1132020-10-25 11:32:17.064 infoUnhandled Event IGNORE THIS - description:read attr - raw: 09530100009001FF4244032828052118000727000000000000000008212312092104186410006510006E20006F200094200395399A99E93D9639C3CB12459739F029243C983920F1B13D9B210000, dni: 0953, endpoint: 01, cluster: 0000, size: 90, attrId: FF01, encoding: 42, command: 0A, value: 44032828052118000727000000000000000008212312092104186410006510006E20006F200094200395399A99E93D9639C3CB12459739F029243C983920F1B13D9B210000 | msgMap:[raw:09530100009001FF4244032828052118000727000000000000000008212312092104186410006510006E20006F200094200395399A99E93D9639C3CB12459739F029243C983920F1B13D9B210000, dni:0953, endpoint:01, cluster:0000, size:90, attrId:FF01, encoding:41, command:0A, value:[raw:[deviceTemperature:28, RSSI_dB:0018, unknown2:0000000000000000, unknown3:1223, unknown4:1804, openClose:00, switch2:00, unknown10:00, unknown11:00, unknown9420:03, consumption:3C2429F0, voltage:4512CBC3, power:3DB1F120, unknown9:0000], deviceTemperature:40, RSSI_dB:24, unknown2:0, unknown3:4643, unknown4:6148, openClose:false, switch2:false, unknown10:0, unknown11:0, unknown9420:3, consumption:0.010019764, voltage:2348.735, power:0.08688569, unknown9:0], clusterInt:0, attrInt:65281]

dev:1132020-10-25 11:32:17.046 warnPLEASE REPORT TO DEV - The Xiaomi Struct used an unrecognized tag: 0x94 (type: 0x20) (struct: 44032828052118000727000000000000000008212312092104186410006510006E20006F200094200395399A99E93D9639C3CB12459739F029243C983920F1B13D9B210000)

dev:1132020-10-25 11:31:51.029 infoUnhandled Event IGNORE THIS - description:catchall: 0104 000A 01 01 0040 00 0953 00 00 0000 00 00 0000 | msgMap:[raw:catchall: 0104 000A 01 01 0040 00 0953 00 00 0000 00 00 0000, profileId:0104, clusterId:000A, clusterInt:10, sourceEndpoint:01, destinationEndpoint:01, options:0040, messageType:00, dni:0953, isClusterSpecific:false, isManufacturerSpecific:false, manufacturerId:0000, command:00, direction:00, data:[00, 00]]

dev:1132020-10-25 11:31:09.039 infoUnhandled Event IGNORE THIS - description:read attr - raw: 095301000C0E55003960E8363E, dni: 0953, endpoint: 01, cluster: 000C, size: 0E, attrId: 0055, encoding: 39, command: 0A, value: 60E8363E | msgMap:[raw:095301000C0E55003960E8363E, dni:0953, endpoint:01, cluster:000C, size:0E, attrId:0055, encoding:39, command:0A, value:3E36E860, clusterInt:12, attrInt:85, valueParsed:0.17862082]

dev:1132020-10-25 11:31:07.335 infoOn/Off Button press - description:read attr - raw: 09530100060800001000, dni: 0953, endpoint: 01, cluster: 0006, size: 08, attrId: 0000, encoding: 10, command: 0A, value: 00 | parseMap:[raw:09530100060800001000, dni:0953, endpoint:01, cluster:0006, size:08, attrId:0000, encoding:10, command:0A, value:00, clusterInt:6, attrInt:0, valueParsed:false]

dev:1132020-10-25 11:31:07.194 infoOn/Off Button press - description:read attr - raw: 0953020006160000100000F0233E000007, dni: 0953, endpoint: 02, cluster: 0006, size: 16, attrId: 0000, encoding: 10, command: 0A, value: 0000F0233E000007 | parseMap:[raw:0953020006160000100000F0233E000007, dni:0953, endpoint:02, cluster:0006, size:16, attrId:0000, encoding:10, command:0A, value:00, clusterInt:6, attrInt:0, additionalAttrs:[[value:0700003E, encoding:23, attrId:F000, consumedBytes:7, attrInt:61440]], valueParsed:false]

dev:1132020-10-25 11:31:07.175 infoON/OFF CATCHALL CLUSTER EVENT - description:catchall: 0104 0006 02 01 0040 00 0953 00 00 0000 0B 01 0000 | parseMap:[raw:catchall: 0104 0006 02 01 0040 00 0953 00 00 0000 0B 01 0000, profileId:0104, clusterId:0006, clusterInt:6, sourceEndpoint:02, destinationEndpoint:01, options:0040, messageType:00, dni:0953, isClusterSpecific:false, isManufacturerSpecific:false, manufacturerId:0000, command:0B, direction:01, data:[00, 00]]

Hope it is useful..

[jorgespneto]

Congratulations, I already did the update. I would like to thank you for all your efforts in helping the community.
Then please see if you can take a look at that Gledopto controller.
I would like to ask a question, is it possible to add in the driver some function to save the last state of the device? in case there is a power failure and when it comes back the device establishes the last saved state

[BrunoVoeten]

FYI

@Royski

Guys just so you are aware, you wont receive any responses from Markus, Eli or April. For some unknown reason they have been suspended from the community forum.

[mark.cockcroft]

Did Marcus ever get back to you on a zigbee driver for this?

[Ranchitat]

@mark.cockcroft

a zigbee driver for this?

Nothing, haven't had a chance to try anything other than load all the drivers I could find for sirens, temps, humidity etc. etc.

Hopefully something comes up on the other thread.

[BrunoVoeten]

Any luck already with connecting the MOES Thermostat?

[coldfuture]

Still no luck. I have ordered tuya hub to upgrade firmware there. Gonna try again after that.

[BrunoVoeten]

The missing device, a working EU zigbee thermostat that works on Hubitat where the repeater function is working well for Xiaomi & Aqara devices...
I need 6 of them...

[akitamostodos]

Hello I have bought a tuya trv, I put driver
Tuya Zigbee Valve (works with Tuya Zigbee Valves and probably any other Zigbee Valve devices using standard clusters)

But didn't work.
Didn't open.. Close... Can't do anything.

I have this device.
€ 24,51 34%OFF | Termostato termostático programable para radiador, controlador de temperatura compatible con Alexa, Tuya Smart ZigBee

US $30.54 34% OFF|Tuya Smart ZigBee Radiator Actuator Programmable Thermostat...

[coldfuture]

I received and installed tuya hub, that moes thermostats work well with tuya hub, but still can't be controlled from hubitat. I have tried every thermostat driver in HE, no reaction to on/off buttons and no info about currently temperature.
But at the same time it works fine as a router. Several devices as aqara motion sensors or ikea bulbs connected through this thermostat.
I'm talking about this device: https://a.aliexpress.com/_mLlYpyZ

[coldfuture]

Have you tried zen thermostat driver?

[mark.cockcroft]

Or this

[RELEASE] eCozy ZigBee Thermostat / TRV

I ported my ST DTH for the eCozy Thermostat to Hubitat. Just required changing one word for it to work. https://github.com/ckpt-martin/Hubitat/blob/master/eCozy/eCozy-ZigBee-Thermostat-Driver.groovy

[BrunoVoeten]

For me it would be ideal, 6 thermostats connected to my Hubitat that work as repeaters for my Aqara sensors in the house.
It is a pity that Hubitat does not support such devices because it is not 100% zigbee while other hubs or drivers do work. There are many popular devices (Ikea, Aqara, Moes ...) that do not work on Hubitat, I am very happy with my Hub, but if there is ever an alternative that can offer this ....

[akitamostodos]

Didn't work for me, it work on your hubitat?

Thanks

[mark.cockcroft]

Not tried yet mine is still in transit

[Ranchitat]

@Ranchitat

Hi Markus, any chance you've got a Generic Zigbee Siren Driver up your sleeve?

This seems to work.

[mattias]

New drivers compatible with HE v 2.2.4 available. [Release] Generic Zigbee Drivers with Presence and Recovery - Markus Project - Oh-La LABS Community

[Bennic]

Hi Markus,

I recently bought a LoraTap 3-gang Tuya switch:

The ic used in this device is TYZS3: https://developer.tuya.com/en/docs/iot/device-development/module/zigbee-module/tyzs-series-module/zigbeetyzs3ipexmodule?id=K989rjm3c1z55

Double press is on, long press is off. This works. With the switch driver.
Can I also use single press?

COPY AND PASTE THIS ROW TO THE DEVELOPER: fingerprint model:"TS0043", manufacturer:"_TZ3000_bi6lpsew", profileId:"0104", endpointId:"01", inClusters:"0000,000A,0001,0006", outClusters:"0019", application:"42"

This is the info from when de device was found:
ID: 917F
Manufacturer: _TZ3000_bi6lpsew
Product Name:
Model Number: TS0043
deviceTypeId: 210
more...
manufacturer : _TZ3000_bi6lpsew
idAsInt : 1
inClusters : 0000,000A,0001,0006
endpointId : 01
profileId : 0104
application : 42
outClusters : 0019
initialized : true
model : TS0043
stage : 4
manufacturer :
idAsInt : 2
inClusters : 0001,0006
endpointId : 02
profileId : 0104
application :
outClusters :
initialized : true
model :
stage : 4
manufacturer :
idAsInt : 3
inClusters : 0001,0006
endpointId : 03
profileId : 0104
application :
outClusters :
initialized : true
model :
stage : 4

Do you think you can make the single press work also?
I hope this is enough info.
Thanks for all your hard work!

[at9]

Markus isn't on the community anymore but check out this thread for a driver that works.

Zemismart Zigbee Smart Remote Switch (3 button) driver

Driver posted by at9 works for me, just buttons 1 and 3 are swapped. You can swap the plastic button covers or modify driver on lines 99 and 105.