Try the new driver. You shouldn't even have to re-pair it. Just swap driver, save, configure, and you should be good!
ok
Regular repeaters won't solve the Schlage issue, you need amplifying repeaters these are the ones I'm referencing. https://www.amazon.com/Aeotec-Range-Extender-Z-Wave-repeater/dp/B01M6CKJXC
Here is the thread that discusses the in depth resolving of the issue Adding Aeotec Range Extenders has made my BE469 and FE599 locks reliable
2 Likes
That was painless. So. what's the difference. Can I do anything new with this driver? I just see the difference of enable lock code encryption. Am I missing some kind of greatness?
According to the release notes:
2.1.3 Schlage BE468/BE469 Lock, additional event decoding for BE469.
2.1.2 Schlage Schlage BE468/BE469 Lock, added missing event decodes.
2.1.1 New drivers: * Schlage BE468/BE469 Lock
I think they mostly deal with Rule Machine and using those codes for automations. I don't think the locks sent the codes before this. There was a thread by I think Mike Maxwell discussing the 2.1.1 difference in the driver, but that reason isn't in the release notes.
Edit for maybe clarity. I think the locks previously sent only "locked" or "unlocked" events and not specific ones like "april's code XYZ" or whatever.
I think I found it.
Did you mean new hub, or just changing to the new Schlage Z-Wave lock drivers? The former is an endeavour that will gain you little besides a slightly prettier hub (if you have/had a C-3 or C-4)--and actually slightly less functionality at the moment since the Z-Wave radio is internal, unless you take your stick with, in which case you've negated the former possible benefit.
The latter, changing the driver, is easy (no need to re-pair, as you've now read) and likely to be problem-free. I switched as soon as they were available and haven't noticed any issues since (except an ongoing apparent bug where Notification child apps trigger on any lock code, not just the specified one, but it's fine in Rule Machine, so I don't think it's a driver or device issue).
The above advice on repeaters is good advice in general, but that is handled at the protocol level, not with the driver, so it won't make a difference here. The Dome and Aeon advertised as being signal "boosters" too, which is confusing to me since "repeater" in my book already means something that receives and re-transmits a therefore-less-attenuated copy of the message it received, but there must be something extra-special about those with the way some people rave about them. FWIW, I don't have the either, but I did switch out all of my Z-Wave repeaters to Plus (not really necessary but I wanted benefits elsewhere--but certainly couldn't hurt here with the range improvements) and made sure as many as possible supported beaming (helpful with "sleepy" devices like locks to take some work off the hub). If you're not sure what your repeaters support, you can check the certification doc on the Z-Wave Alliance site.
I updated the driver. Thanks for the input on this one. I'll see how it rolls. If it reports who unlocked the door, I'm all in.
1 Like
This will work for user codes were added using Hubitat (eg. using LCM). For codes added directly at the lock, I think you'll only get the slot number.
I was just looking around to find some rule examples of this. Can you help me with the variable?
I haven't tested it, but I think you should be able to use a rule like this:
I do use this lock code rule (Pattie Poehl is a virtual switch that turns on when the maid unlocks the door using her lock code)
So do I need to have a rule for every user? Or is there a universal way to announce any code/user entered?
Check the first rule. You should have a choice for "Any Lock Code". If you use that rule, then "%value%" would be the specific lock code used.
I'm 99% sure that I used "Any Lock Code" during testing Rule 3.0 and it worked.
this is also something I need to set up for my cleaning person too!
Any way to get the name instead of the code?
Some automations bother the person who cleans my house, so I turn them off using a virtual switch that is turned on when she arrives.
Try it. I think if the code is mapped to a name using Lock Code Manager, the announcement will use the name. I'm not home right now, but I can try it tonight.
My person has poltergeist going on in my house as my qi chargers control quiet time and night and the lighs turn on and off when she's moving them around. I have to chuckle becuase my phone announces mode changes. She's all cool with technology, but I'd like to convenience her with a few things like lights staying on for her.
1 Like
I will do that. Thank you very much for the input. It gives me a starting point. I was taking that path, but got stuck on my choices.
The Siren 6/Doorbell 6 is also a beaming repeater as well.
1 Like
