Agreed...
Do you see anything special about the configuration parameters being sent to these bulbs in the ST DTH?
Nothing in there, that's as about as basic as a driver gets...
2 Likes
@mike.maxwell the only thing that I see is on/off reporting is set to a minimum of 0 seconds. Is that what you’re setting it to in the HE driver?
Just on/off reporting set to a 0 sec min, 300 max. Wonder what HE sets the minimum to?
What bulb did you order? May have to play around with the sniffer to see what is in the conversation pairing it to ST.
I must say I do have the upmost respect for the OP for having the patience to go back to SmartThings.
I left that platform for Homeseer and on to Hubitat. It’s been maybe a year I forgot to stop the system down emails from Smarthings and like clockwork they still come in like once every 2 weeks saying the system is down for some stupid reason.
Me and my wife’s patience wore thin with Smarthings going down and leaving us high and dry with no automations so I switched to Homeseer then to Hubitat because of HSM, my point being I wish I was as patient with Smarthings and stayed with them to save some time and money but if I did I would have had to slam my head against a brick wall dealing with there platform being down so often.
3 Likes
I still have my house on ST, my condo is on Hubitat and I plan to use Hubitat at my next condo this summer.
After using Hubitat at my condo in a relatively simple setup - Hubitat is great but not perfect. I could say the same about ST.
If my ST Hub at home were to fail I would likely replace it with Hubitat but I would have to sacrifice some features (actiontiles - need pin on HSM time, WebCoRE, Knock detection, Stringify, mobile app, unlimited text alerts, etc...)
I have over a hundred devices connected to my ST setup at home. I will switch to Hubitat if SmartThings goes downhill (Hun failure or new app) OR if Hubitat matches/exceeds ST features and 3rd party app don’t result in crashes. I am hoping on the latter.
Btw any Rule Machine experts? I need help with this: Connecting August Lock Pro
This is the Sengled bulb I ordered. It is the same model that @toyanucci mentioned in an earlier post.
It would be great to have you analyze the traffic to see what is going on. Thanks!
https://www.amazon.com/gp/product/B01N7I4X94/ref=ppx_yo_dt_b_asin_title_o00__o00_s00?ie=UTF8&psc=1
4 Likes
Just ordered one... Still have SmartThings in the basement so I'll capture that conversation and see what I find. 
4 Likes
It's also great for status...
2 Likes
Especially when troubleshooting failed automations..
2 Likes
Currently cluster 0006 reporting is disabled for bulbs, I am slowly working through a different reporting config for bulbs, when I get to testing this, I'll check what each of the bulbs I own report at mains on and off if anything.
5 Likes
I wrote about this issue a couple of weeks back. Thanks for adding the video @toyanucci to make the point.
I've got a couple of dumb switched smart bulb locations where the kids would turn these switches on and leave them on. Both locations don't have a neutral wire so it makes sense to leave them as is with a smart bulb.
I'd forgotten about having webcore rules that handled turning these smart bulbs off after x minutes if found on and how the state of these bulbs showed up properly in the Smartthings App. Over the years I had Cree, GE, and Sengled bulbs in these 2 figures. So the manufacturer of bulbs apparently did not matter.
As @toyanucci wrote this breaks automations and refreshing or polling as I'm doing now is not the answer.
I'll do the same when the Sengled arrives (unless you have one already). Since HE is not processing those reports, and ST is, my educated guess is the bulb is setting an on/off report when it loses power and the hub is not parsing it.
This should be an easy test by porting the generic ST Zigbee driver and seeing if that corrects the behavior.
ACKmySYN,
Another thanks for posting the example. I'm yet another Iris user looking for a home, wandering the forums trying to fully understand the options, and make a decision on a replacement system that has minimal impact to the WAF (Wife Acceptance Factor). Iris absolutely had it's faults, but I did not think finding a replacement would take this much effort. I'm trying to avoid two systems to close the gap with basic simple security and automation, but it's taking a good bit of research. And I will also say that the responsiveness of the Hubitat forums is nice.
Hey, probably no one will believe me but I ported the ST driver, installed it to a sengled color, clicked configure, it reports I turned it off and on in the dumb switch!
/**
* Copyright 2015 SmartThings
*
* Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
* in compliance with the License. You may obtain a copy of the License at:
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
* on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
* for the specific language governing permissions and limitations under the License.
*
*/
metadata {
definition (name: "ZigBee Dimmer", namespace: "smartthings", author: "SmartThings", ocfDeviceType: "oic.d.light", runLocally: true, minHubCoreVersion: '000.019.00012', executeCommandsLocally: true) {
capability "Actuator"
capability "Configuration"
capability "Refresh"
capability "Switch"
capability "Switch Level"
capability "Health Check"
capability "Light"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008", outClusters: "0019", manufacturer: "Aurora", model: "LCBulb01UK", deviceJoinName: "Aurora AOne Control Dimmer (120w)"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008", outClusters: "0019", manufacturer: "LEEDARSON LIGHTING", model: "M350ST-W1R-01", deviceJoinName: "OZOM Dimmable LED Smart Light"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300", outClusters: "0003", manufacturer: "Aurora", model: "Dimmer", deviceJoinName: "Aurora AOne Control Dimmer (320w)"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0B04, FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY A19 ON/OFF/DIM", deviceJoinName: "SYLVANIA Smart A19 Soft White"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY A19 ON/OFF/DIM 10 Year", deviceJoinName: "SYLVANIA Smart 10-Year A19"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, FF00", outClusters: "0019", manufacturer: "MRVL", model: "MZ100", deviceJoinName: "Wemo Bulb"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0B05", outClusters: "0019", manufacturer: "OSRAM SYLVANIA", model: "iQBR30", deviceJoinName: "Sylvania Ultra iQ"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY PAR38 ON/OFF/DIM", deviceJoinName: "SYLVANIA Smart PAR38 Soft White"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0B04, FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY BR ON/OFF/DIM", deviceJoinName: "SYLVANIA Smart BR30 Soft White"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0702, 0B05", outClusters: "0019", manufacturer: "sengled", model: "E11-G13", deviceJoinName: "Sengled Element Classic"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0702, 0B05", outClusters: "0019", manufacturer: "sengled", model: "E11-G14", deviceJoinName: "Sengled Element Classic"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0702, 0B05", outClusters: "0019", manufacturer: "sengled", model: "E11-G23", deviceJoinName: "Sengled Element Classic"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0702, 0B05", outClusters: "0019", manufacturer: "sengled", model: "E11-G33", deviceJoinName: "Sengled Element Classic"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0702, 0B05", outClusters: "0019", manufacturer: "sengled", model: "E12-N13", deviceJoinName: "Sengled Element Classic"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0702, 0B05", outClusters: "0019", manufacturer: "sengled", model: "E12-N14", deviceJoinName: "Sengled Element Classic"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0702, 0B05", outClusters: "0019", manufacturer: "sengled", model: "E12-N15", deviceJoinName: "Sengled Element Classic"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008", outClusters: "0003, 0006, 0008, 0019, 0406", manufacturer: "Leviton", model: "DL6HD", deviceJoinName: "Leviton Dimmer Switch"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008", outClusters: "0003, 0006, 0008, 0019, 0406", manufacturer: "Leviton", model: "DL3HL", deviceJoinName: "Leviton Lumina RF Plug-In Dimmer"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008", outClusters: "0003, 0006, 0008, 0019, 0406", manufacturer: "Leviton", model: "DL1KD", deviceJoinName: "Leviton Lumina RF Dimmer Switch"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300, 0B04, 0B05, FC01, FC08", outClusters: "0003, 0019", manufacturer: "LEDVANCE", model: "A19 W 10 year", deviceJoinName: "SYLVANIA Smart 10Y A19 Soft White"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300, 0B05, FC01", outClusters: "0003, 0019", manufacturer: "LEDVANCE", model: "BR30 W 10 year", deviceJoinName: "SYLVANIA Smart 10Y BR30 Soft White"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300, 0B05, FC01", outClusters: "0003, 0019", manufacturer: "LEDVANCE", model: "PAR38 W 10 year", deviceJoinName: "SYLVANIA Smart 10Y PAR38 Soft White"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008", outClusters: "0003, 0006, 0008, 0019, 0406", manufacturer: "Leviton", model: "ZSD07", deviceJoinName: "Leviton Lumina RF 0-10V Dimming Wall Switch"
fingerprint profileId: "0104", inClusters: "0000, 0004, 0003, 0006, 0008, 0005, FFFF, 1000", outClusters: "0019", manufacturer: "LDS", model: "ZBT-DIMLight-GLS0000", deviceJoinName: "A60 Dim Bulb"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008", outClusters: "0019", manufacturer: "LDS", model: "ZHA-DIMLight-GLS0000", deviceJoinName: "A60 Dim Bulb"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 1000", outClusters: "0019", manufacturer: "LDS", model: "ZBT-DIMLight-GLS", deviceJoinName: "A60 Dim Bulb"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 1000", outClusters: "0019", manufacturer: "LDS", model: "ZBT-DIMLight-GLS0044", deviceJoinName: "智能球泡灯(可调光版)"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0009", outClusters: "0019", manufacturer: "Aurora", model: "FWMPROZXBulb50AU", deviceJoinName: "Aurora MPro"
fingerprint profileId: "0104", inClusters: "0000, 0004, 0003, 0006, 0008, 0005, FFFF, 1000", outClusters: "0019", manufacturer: "Aurora", model: "FWBulb51AU", deviceJoinName: "Aurora Smart Dimmable"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008", outClusters: "0019", manufacturer: "Aurora", model: "FWStrip50AU", deviceJoinName: "Aurora Dimmable Strip Controller"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0B05, 1000, FEDC", outClusters: "000A, 0019", manufacturer: "Aurora", model: "FWGU10Bulb50AU", deviceJoinName: "Aurora Smart Dimmable GU10"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0B05, 1000, FEDC", outClusters: "000A, 0019", manufacturer: "Smarthome", model: "S111-201A", deviceJoinName: "Leedarson Dimmable White Bulb A19"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 1000", outClusters: "0019", manufacturer: "innr", model: "RB 265", deviceJoinName: "Innr Smart Bulb White"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 1000", outClusters: "0019", manufacturer: "innr", model: "RB 245", deviceJoinName: "Innr Smart Candle Warm White"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 1000", outClusters: "0019", manufacturer: "innr", model: "RS 225", deviceJoinName: "Innr Smart Spot White"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0702, 0B05", outClusters: "0019", manufacturer: "sengled", model: "E11-N13", deviceJoinName: "Sengled Element Classic"
fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0702, 0B05", outClusters: "0019", manufacturer: "sengled", model: "E11-N14", deviceJoinName: "Sengled Element Classic"
}
tiles(scale: 2) {
multiAttributeTile(name:"switch", type: "lighting", width: 6, height: 4, canChangeIcon: true){
tileAttribute ("device.switch", key: "PRIMARY_CONTROL") {
attributeState "on", label:'${name}', action:"switch.off", icon:"st.switches.light.on", backgroundColor:"#00A0DC", nextState:"turningOff"
attributeState "off", label:'${name}', action:"switch.on", icon:"st.switches.light.off", backgroundColor:"#ffffff", nextState:"turningOn"
attributeState "turningOn", label:'${name}', action:"switch.off", icon:"st.switches.light.on", backgroundColor:"#00A0DC", nextState:"turningOff"
attributeState "turningOff", label:'${name}', action:"switch.on", icon:"st.switches.light.off", backgroundColor:"#ffffff", nextState:"turningOn"
}
tileAttribute ("device.level", key: "SLIDER_CONTROL") {
attributeState "level", action:"switch level.setLevel"
}
}
standardTile("refresh", "device.refresh", inactiveLabel: false, decoration: "flat", width: 2, height: 2) {
state "default", label:"", action:"refresh.refresh", icon:"st.secondary.refresh"
}
main "switch"
details(["switch", "refresh"])
}
}
// Parse incoming device messages to generate events
def parse(String description) {
log.debug "description is $description"
def event = zigbee.getEvent(description)
if (event) {
if (event.name=="level" && event.value==0) {}
else {
sendEvent(event)
}
} else {
def descMap = zigbee.parseDescriptionAsMap(description)
if (descMap && descMap.clusterInt == 0x0006 && descMap.commandInt == 0x07) {
if (descMap.data[0] == "00") {
log.debug "ON/OFF REPORTING CONFIG RESPONSE: " + cluster
sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
} else {
log.warn "ON/OFF REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
}
} else if (device.getDataValue("manufacturer") == "sengled" && descMap && descMap.clusterInt == 0x0008 && descMap.attrInt == 0x0000) {
// This is being done because the sengled element touch/classic incorrectly uses the value 0xFF for the max level.
// Per the ZCL spec for the UINT8 data type 0xFF is an invalid value, and 0xFE should be the max. Here we
// manually handle the invalid attribute value since it will be ignored by getEvent as an invalid value.
// We also set the level of the bulb to 0xFE so future level reports will be 0xFE until it is changed by
// something else.
if (descMap.value.toUpperCase() == "FF") {
descMap.value = "FE"
}
sendHubCommand(zigbee.command(zigbee.LEVEL_CONTROL_CLUSTER, 0x00, "FE0000").collect { new hubitat.device.HubAction(it) }, 0)
sendEvent(zigbee.getEventFromAttrData(descMap.clusterInt, descMap.attrInt, descMap.encoding, descMap.value))
} else {
log.warn "DID NOT PARSE MESSAGE for description : $description"
log.debug "${descMap}"
}
}
}
def off() {
zigbee.off()
}
def on() {
zigbee.on()
}
def setLevel(value) {
def additionalCmds = []
if (device.getDataValue("model") == "iQBR30" && value.toInteger() > 0) { // Handle iQ bulb not following spec
additionalCmds = zigbee.on()
} else if (device.getDataValue("manufacturer") == "MRVL") { // Handle marvel stack not reporting
additionalCmds = refresh()
}
zigbee.setLevel(value) + additionalCmds
}
/**
* PING is used by Device-Watch in attempt to reach the Device
* */
def ping() {
return zigbee.onOffRefresh()
}
def refresh() {
zigbee.onOffRefresh() + zigbee.levelRefresh()
}
def installed() {
if (((device.getDataValue("manufacturer") == "MRVL") && (device.getDataValue("model") == "MZ100")) || (device.getDataValue("manufacturer") == "OSRAM SYLVANIA") || (device.getDataValue("manufacturer") == "OSRAM")) {
if ((device.currentState("level")?.value == null) || (device.currentState("level")?.value == 0)) {
sendEvent(name: "level", value: 100)
}
}
}
def configure() {
log.debug "Configuring Reporting and Bindings."
// Device-Watch allows 2 check-in misses from device + ping (plus 1 min lag time)
// enrolls with default periodic reporting until newer 5 min interval is confirmed
sendEvent(name: "checkInterval", value: 2 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
// OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
refresh() + zigbee.onOffConfig(0, 300) + zigbee.levelConfig()
}
4 Likes
Sure would like to have that driver or a link to it.
1 Like
Awesome! I believe you, but I have to try it for myself tonight when I get home.
Please share the ported driver. Thanks!
1 Like
I just added the driver in my post.
1 Like
To make sure I understand... you ported the non-color driver, and are using it with a color bulb just for testing, correct?
Have you tried to port the color bulb driver as well?
Yes,
I don't know where is the color driver for sengled. I can try.
