I'd look at Aurora double sockets, that's what I have on mine.
You get power monitoring per socket.
What some don't realise is that regardless of whether it is a single or double socket - it is rated at 13 Amps as a whole. Just because it'll take two BS1363 plugs with a 13Amp fuse in each doesn't mean you should do that.
If you can't find a plug look at using a current sensing switch. Works amazingly.
I got the idea from another thread on this forum (that I can't find). Basically you put it around one of the legs of the power going into the back of the plug and connect it to any kind of sensor that accepts external input. I used a ecolink contact switch for this to bring it in a zwave.
The install was much easier than I expected. Took me 10 minutes. Just had to take the panel off the back, unscrew the leg to feed it through the switch and screw it back in. Set it up in HE and the switch will send on/off based on the status of the dryer. It doesn't need external power. It generates just enough power from sensing to trigger the switch.
I did try vibration sensors but you will go through a lot of batteries as the sensor will constanly be active throughout the cycle. The second sensor I tried just flooded the network with reports. So wasn't worth the headache.
My washer uses much less power so I use a power sensing switch for that as it can handle the load. But I may want to change that over eventually as well.
https://www.amazon.ca/gp/product/B07N4RQP4B
You may want to get a normally closed one. That way the switch is closed when its off and open when its on. Either way you can adjust the logic in HE.
1 Like
So where else are we supposed to plug in our appliances? No different than a standard UK socket is it?
If you had two high consumers in a kitchen - Washing Machine & Dishwasher as an example, and there was a chance that they would be running simultaneously, the solution is just to have two single sockets as each is rated at 13 Amps.
I believe the thread was this one, which I recommend @NiallG might want to scan through for the discussion of the issues with using power monitoring for the washer.
2 Likes
Rated for 25A
Or a circuit breaker
1 Like
I use these too.
I wish we could sort out how to disable the local on|off switching of the sockets though.
Found the original thread I got the idea from.
You can, but sadly not included in the driver.
My workaround for some (like the fridge) is, if its turned off, turn back on.
Works a treat 
Unfortunately that messes up the programming on my washing machine though, it doesn’t resume.
I have some aurora doubles power monitoring is not great imho, i have click smart single and doubles no power mointering.
Both the aurora and clicksmart are my preferred as they are not plugin sockets.
I have various gen of smartthing plug in sockets all work very well and a few aeotec ones which imho give the best power monitoring.
You can do that with the Fibaro outlets. It's not feature as such - they simply stop working after a few weeks - I've had 3 fail 
No, I'm not interested in its power consumption.
I want to know when it's finished. Laundry room's at the other end of the house, no reason to go there unless we're putting washing in, or taking it out. A power reporting plug would trigger a notification when it's done.
Ok, someone was saying that the sensor burns through batteries because it's constantly picking up vibration until it's not when the machine is finished.
I take it you mean the Fibaro FGWPG-111 plug? That's very interesting, thank you for that info. My machine is AEG as well, rated at 2200W.
I don't know the ins and outs of all the electrical stuff (that's why I'm on here!), just reporting what the Innr engineer wrote.
He said to me 'don't use anything with an inductive load on it', and that's a washing machine.
That's an interesting option, I'll look at that...
@NiallG Yes I have the FGWPG-111 plug. My AEG (for reference) is the 7000 series model number L7FC8432BI.
I appreciate that and although I'm electrically qualified I thought I'd take a quick peak at the Fibaro website....see the icons in the image below:
Fair to say that's a washing machine!
Perhaps, I have been using this method for a couple years now and I think I have changed the battery twice. The first battery did seem to go out pretty quickly, but the two replacements have seemed to last long enough that I haven't consider it a problem. I don't know exactly how long they last, I changed the last battery some time in the last 3 to 6 months as I remember. and it is currently at 85%. It's one of the smartthings multi sensors, not sure your can get them anymore.
I am now using this device note app to add a note of the battery type and when I changed it last to any device when I change a battery, so maybe once I start really keeping track of it I may consider it too short. My memory for stuff like this is bad so maybe I am switching them more often.
Heh heh, I just saw that washing machine icon on the Fibaro website before I came back on here.
Looks like I'll go for that one...does it pair with the Hubitat easily?
